Industrial Laser Solutions

DMK Continuous Wave (CW) Laser Cleaners

$14,600.00 AUD

Sale Sold out

Power output 2000 Watt - Single axis beam pattern 2000 Watt - Daul Axis beam pattern 3000 Watt - Daul Axis beam pattern 3000 Watt - Single axis beam patten

Quantity

Continuous Wave (CW) laser cleaners emit a constant, non-stop beam of laser energy rather than short bursts like a pulse laser. This more aggresive delivery method relies on thermal ablation to superheat dirt, rust, or surface coatings until they vaporize or peel off instantly.

More heat can be transfered in the part being cleaned, so they are more suited for use on thick walled parts or items with a larger mass that can dissipate the heat more effectively. Depending on the machine settings and substrate the beam can remove rust or a surface coating and leave behind a textured finish on the surface of part.

They are typically used for

Rust removal
Paint and Surface coating removal
Cleaning (removal of oil, soot, stain and algae and other suface build up)
Surface preparation (texturing or keying of a surface prior to coating

The CW machines are typically water cooled to allow for greater duty cycles and are larger units. Power requirements vary depending on the output power of the unit but most CW cleaners require 3 phase and up to 60 amp curcuits so are typicaly aimed for industrial use.

We offer the machine with two types of scanning heads as listed below:

Single Axis: Single straight line beam profile

Dual Axis : Muliple beam profiles

Type	DCL-2000	DCL-3000
Laser source	CW Fiber	CW Fiber
Laser Power	2000W	3000W
Fiber cable	10-20 M	10-20M
Wavelength	1070nm	1070nm
Clean speed	≤50M²/Hour	≤80M²/Hour
Beam width	10-150mm	10-200mm
Scann speed	0-7000mm/s	0-7000mm/s
Cooling	Water cooling	Water cooling
Voltage	Three Phase 415 Volt AC, 50HZ	Three Phase 415 Volt AC, 50HZ

Shipping & Returns

Shipping Information

 Shipping Locations
We ship Australia-wide and may offer international shipping on selected items
(please check product listings or contact us for details).
 Shipping Costs
Shipping costs are calculated at checkout and are based on order size, weight, and
delivery location.
 Delivery Times
Orders are usually dispatched within 1–3 business days after payment confirmation.
Delivery times vary depending on your location, but standard shipping within
Australia typically takes 3–7 business days.
Please note: Delivery times are estimates only, and we are not responsible for delays
caused by couriers, customs, or factors outside our control.
 Tracking
Once your order is shipped, you will receive tracking details via email so you can
monitor the progress of your delivery.

Returns and Exchanges

We want you to be happy with your purchase. If you need to return an item, please follow the
steps below.

1.) Faulty or Damaged Items
If your item arrives damaged or faulty:
 Contact us at sales@industriallaser.com.au within 7 days of receiving your order.
 Provide your order number, details of the fault/damage, and (if possible) a photo.
 We will issue you an RMA (Return Merchandise Authorisation) number.
 Return the item with the RMA number clearly included inside the box.
Once we receive and inspect the item, we will offer you a refund, replacement, or repair in
line with Australian Consumer Law.

2.) Change of Mind Returns

If you change your mind:
 Contact us at sales@industriallaser.com.au within 7 days of receiving your order.
 We will issue you an RMA number.
 Return the unused, unopened item in its original packaging with the RMA number
inside the box.
 You are responsible for return shipping costs.
 A restocking fee of 15% may apply.
Once we receive and inspect the returned item, we will process your refund (excluding
original shipping fees and any restocking fees).

Important Notes
 No returns will be accepted without an RMA number.
 Returns must be sent back within 7 days of receiving your RMA.
 We recommend using a tracked service

View full details

DMK SA2000W